Team Associated RC10B6.2 - B6.2 Maastosarja 2 2021 Oulu - Hard front arms
Front End
| Parameter | Value |
|---|---|
| Anti Roll Bar | Not selected |
| Arm flex | Hard |
| Arm type | Gull |
| Axle height | +2 |
| Bulkhead type | Aluminium |
| Bumpsteer Washer | 2 mm |
| Camber | -2 ° |
| Camber link inside height | 1 mm |
| Camber link inside location | Inside |
| Camber link outside location | Inside |
| Caster Block insert | 5° |
| Caster Block Spacing | 1 mm |
| Eyelet length | Short |
| Kick-Up angle | 25° |
| Ride Height | 16 mm |
| Shock cup offset | 5mm |
| Shock limiter | 2 mm |
| Shock mounting lower | Middle |
| Shock mounting upper | Middle |
| Shock oil | AE 32,5 |
| Shock piston | 2 x 1.6 thin |
| Shock Spring | AE Red V2 |
| Shock stroke | 22 mm |
| Shock tower | Gull wing |
| Steering block | 4 mm |
| Steering plate | +1 |
| Steering Rack Spacers | 2 mm |
| Steering Stop Spacing: | N/A |
| Toe in | 0 ° |
| Wheel hex | 5 mm |
Rear End
| Parameter | Value |
|---|---|
| Arm flex | Standard |
| Block C insert position | Middle outside |
| Block C insert type | 1° |
| Block C type | Standard |
| Block D insert position | Middle inside |
| Block D insert type | 1° |
| Block D type | Standard |
| Camber | -2 ° |
| Camber link inside height | 1 mm |
| Camber link inside location | Middle |
| Camber link outside height | 2 mm |
| Camber link outside location | 2 mm |
| CVA axle drive shaft pin location | +2 |
| Differential Height | 2 |
| Drive shaft length | 67mm |
| Eyelet length | Short |
| Hub insert | +1mm |
| Hub Spacing | Back |
| Hub type | Standard |
| Lower rear arm length | 73 |
| Rear hex width | 6 mm |
| Ride Height | 16 mm |
| Shock cup offset | 5mm |
| Shock limiter | 1 mm |
| Shock mounting lower | B |
| Shock Mounting Position | Front of arm |
| Shock mounting upper | Outside |
| Shock oil | AE 30 |
| Shock piston | 2 x 1.7 thin |
| Shock Spring | AE Blue V2 |
| Shock stroke | 29 |
| Shock tower | Standard |
| Wheelbase shim | Rear |
Chassis
| Parameter | Value |
|---|---|
| Battery placement | N/A |
| Bodyshell | Kit body |
| Car weight | N/A |
| Chassis length | Dirt |
| Chassis weights | N/A |
| Front wing | AE |
| Rear Wing | N/A |
| Side Rails type | Standard |
| Transmission type | 3 Gear Lay Down |
| Wing angle | Not selected |
Drivetrain
| Parameter | Value |
|---|---|
| Diff setting Rear | 3k |
| Final Drive Ratio | |
| Internal Gear Ratio | |
| Pinion | 22 Tooth |
| Rear differential type | Gear |
| Slipper | N/A |
| Slipper notes | N/A |
| Slipper pads | Not selected |
| Slipper setting | N/A |
| Spur gear | 78 Tooth |
Electronics
| Parameter | Value |
|---|---|
| Batteries | reedy 4800 -> reedy 4100 slim |
| Brake EPA | N/A |
| Brake expo | N/A |
| ESC | Reedy 510 |
| ESC setting | N/A |
| Motor | Reedy Mach3 6.5 |
| Motor timing | 20 ° |
| Radio | Sanwa M12 |
| Servo | Reedy |
| Steering EPA left | N/A |
| Steering EPA right | N/A |
| Steering expo | N/A |
| Throttle expo | N/A |
General
| Parameter | Value |
|---|---|
| Setup Notes | N/A |