Team Associated B64 - B64 Aloitus setup - Rear End - Wheelbase: Short->Medium
Front End
| Parameter | Value |
|---|---|
| Anti Roll Bar | |
| Arm flex | Standard |
| Arm mount A block type | |
| Arm mount B block type | |
| Axle height | +1 |
| Bumpsteer Washer | 1 mm |
| Bushing type A | 1° |
| Bushing type B | 1° |
| Camber | -1 ° |
| Camber link inside height | Top |
| Camber link inside location | Outside |
| Camber link outside height | 1 mm |
| Caster Block | 10° |
| Eyelet length | |
| Input arm for bell cranck | |
| Ride Height | 20 mm |
| Rollcenter FF | Lower center |
| Rollcenter FR | Upper center |
| Shock cup offset | 5mm |
| Shock limiter | 2 mm |
| Shock mounting lower | Outside |
| Shock mounting upper | Middle |
| Shock oil | 32.5 |
| Shock piston | 3x1.4 taper |
| Shock Spring | Blue |
| Shock stroke | 21 mm |
| Spacer FF | LRC |
| Spacer FR | LRC |
| Steering block arms | std |
| Steering Rack position | Not selected |
| Steering rack spacers | 0 mm |
| Toe in | 0 ° |
| Wheel hex | std |
| Wheelbase shim |
Rear End
| Parameter | Value |
|---|---|
| Anti Roll Bar Rear | Blue |
| Arm mount C block type | Not selected |
| Arm mount D block type | LRC |
| Camber | -1 ° |
| Camber link inside height | Middle |
| Camber link inside location | Outside |
| Camber link outside height | 0 mm |
| Camber link outside location | Not selected |
| Eccentric Bushing RF | 0° |
| Eccentric Bushing RR | 0° |
| Eyelet length | |
| Hub height | +1mm |
| Offset | std |
| Ride Height | 20 mm |
| Rollcenter RF | Center |
| Rollcenter RR | Center |
| Shock cup offset | 5mm |
| Shock limiter | 0 mm |
| Shock mounting lower | Inside |
| Shock oil | 27.5 |
| Shock piston | 3x1.4 taper |
| Shock Spring | AE Green |
| Shock stroke | 27.5 |
| Shock upper mounting | Middle |
| Wheelbase | Medium |
| Wheelbase shim |
Chassis
| Parameter | Value |
|---|---|
| Battery placement | Middle |
| Bodyshell | Kit |
| Car weight | g |
| Chassis weights | |
| Diff shim (front) | Not selected |
| Diff shim (rear) | Not selected |
| Front ballast weight | g |
| Front wing | JC-high clearance wide |
| Rear brace type | Not selected |
| Wing angle | 3 |
| Wing type | Kit |
Drivetrain
| Parameter | Value |
|---|---|
| Center differential gears | Slipper |
| Diff setting Center | cSt |
| Diff setting Front | 10000 cSt |
| Diff setting Rear | 10000 cSt |
| Final Drive Ratio | |
| Front differential gears | Plastic |
| Internal Gear Ratio | |
| Pinion | 18 Tooth |
| Rear differential gears | Plastic |
| Slipper | On |
| Slipper notes | |
| Slipper pads | 3 pads |
| Slipper setting | 7.0mm mm |
| Spur gear | 81 Tooth |
Electronics
| Parameter | Value |
|---|---|
| Batteries | Reedy 3600 Zappers |
| Brake EPA | % |
| Brake expo | % |
| ESC | Reedy Black Box 510 |
| ESC setting | |
| Motor | Reedy sonic mach 3 6.5 |
| Motor timing | 20 ° |
| Radio | Sanwa M12S |
| Servo | XP Digital 1015 |
| Steering EPA left | % |
| Steering EPA right | % |
| Steering expo | % |
| Throttle EPA | 100 % |
| Throttle expo | % |
General
| Parameter | Value |
|---|---|
| Setup Notes | rear camber link inside: middle out |